LSI MegaRAID SCSI 320-2 RAID Controller Series 518 User Manual Page 100
- Page / 158
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
7-6 Installing and Configuring Clusters
Copyright © 2002 by LSI Logic Corporation. All rights reserved.
Table 7.1 shows which nodes and storage devices should be powered on
during each step.
Before installing the Cluster Service software you must follow the steps
below:
• Install Windows 2000 Advanced Server or Windows 2000 Datacenter
Server on each node
• Set up networks
• Set up disks
Note: These steps must be completed on every cluster node
before proceeding with the installation of Cluster Service on
the first node.
To configure the Cluster Service on a Windows 2000-based server, you
must be able to log on as administrator or have administrative
permissions on each node. Each node must be a member server, or
must be a domain controller inside the same domain. A mix of domain
controllers and member servers in a cluster is not acceptable.
Table 7.1 Nodes and Storage Devices
Step Node 1 Node 2 Storage Comments
Set Up Networks On On Off Make sure that power to all storage devices
on the shared bus is turned off. Power on
all nodes.
Set up Shared Disks On Off On Power down all nodes. Next, power on the
shared storage, then power on the first
node.
Verify Disk Configuration Off On On Shut down the first node. Power on the
second node.
Configure the First Node On Off On Shut down all nodes. Power on the first
node.
Configure the Second
Node
On On On Power on the second node after the first
node was successfully configured.
Post-installation On On On All nodes should be active.
- MegaRAID 1
- SCSI 320-2 1
- RAID Controller 1
- HARDWARE 1
- FCC Regulatory Statement 3
- Logical Drive Configuration 8
- Physical Device Layout 10
- Contents 15
- Contents xvii 17
- Contents xix 19
- Chapter 1 21
- Overview 21
- 1.2 NVRAM and Flash ROM 22
- 1.3 SCSI Connectors 22
- 1.7 Documentation 23
- • MegaRAID Manager 24
- • Power Console Plus 24
- Chapter 2 25
- Introduction to RAID 25
- 2.1.2 Increased Reliability 26
- 2.2.1 Host-Based RAID 26
- 2.3 RAID Overview 27
- 2.3.3 Consistency Check 28
- 2.3.4 Fault Tolerance 28
- 2.3.5 Disk Striping 28
- RAID Overview 2-5 29
- MegaRAID Controller 29
- 2.3.6 Disk Mirroring 30
- 2.3.7 Disk Spanning 31
- 2.3.8 Parity 32
- 2.3.9 Hot Spares 32
- 2.3.10 Hot Swapping 33
- 2.3.11 Disk Rebuild 33
- 2.3.12 Logical Drive States 34
- 2.3.13 SCSI Drive States 34
- 2.3.14 Disk Array Types 35
- 2.3.15 Enclosure Management 35
- 2-12 Introduction to RAID 36
- Chapter 3 37
- RAID Levels 37
- 3.2 RAID 0 38
- 3.3 RAID 1 39
- 3.4 RAID 5 40
- Figure 3.3 RAID 5 Array 41
- 3.5 RAID 10 42
- 3.6 RAID 50 43
- Figure 3.5 RAID 50 Array 44
- Chapter 4 45
- Features 45
- 4-2 Features 46
- 4.1 SMART Technology 47
- 4.2 Configuration on Disk 47
- 4.3 Configuration Features 47
- 4.5 RAID Management Features 49
- 4.6 Fault Tolerance Features 50
- 4.7 Software Utilities 50
- 4.10 MegaRAID Components 52
- 4.10.2 Cache Memory 53
- 4.10.3 MegaRAID BIOS 53
- 4.10.4 Onboard Speaker 53
- 4.10.5 Serial Port 53
- 4.10.6 SCSI Bus 54
- 4.10.7 SCSI Connectors 54
- 4.10.8 SCSI Termination 54
- 4.10.9 SCSI Firmware 54
- 4.11 RAID Management 55
- 4.12 Compatibility 56
- Chapter 5 57
- Configuring Physical Drives 57
- Arrays, and Logical Drives 57
- 5.1.5 Physical Device Layout 62
- 5.2 Configuring Arrays 65
- 5.3 Creating Logical Drives 66
- 5.3.2 Assigning RAID Levels 68
- 5.4 Configuring Logical Drives 69
- Chapter 6 73
- Hardware Installation 73
- 6.2 Installation Steps 74
- 6.2.1 Step 1: Unpack 75
- 6.2.2 Step 2: Power Down 75
- 6-4 Hardware Installation 76
- 6-6 Hardware Installation 78
- 6.2.5 Step 5: Set Termination 80
- Installation Steps 6-9 81
- 6-10 Hardware Installation 82
- Installation Steps 6-11 83
- • Tape drive set to SCSI ID 2 84
- Installation Steps 6-13 85
- Installation Steps 6-15 87
- 6-16 Hardware Installation 88
- Installation Steps 6-17 89
- 6-18 Hardware Installation 90
- 6.2.11 Step 11: Power Up 92
- 6.3 Summary 93
- 6-22 Hardware Installation 94
- Chapter 7 95
- Installing and Configuring 95
- Clusters 95
- 7.2 Benefits of Clusters 96
- Advanced Server 97
- 7.3.2 Network Requirements 98
- 7.4 Cluster Installation 99
- • Set up networks 100
- • Set up disks 100
- 7.4.3 Setting Up Networks 101
- Cluster Installation 7-9 103
- Cluster Installation 7-13 107
- Cluster Installation 7-15 109
- Cluster Installation 7-17 111
- Cluster Installation 7-19 113
- Cluster Installation 7-21 115
- Cluster Installation 7-23 117
- Cluster Installation 7-25 119
- 7.4.18 Verifying Installation 120
- 7.5 Installing SCSI Drives 121
- Chapter 8 123
- Troubleshooting 123
- Firmware Initializing 124
- 8.2 BIOS Boot Error Messages 125
- 8.3 Other BIOS Error Messages 127
- 8.4 Other Potential Problems 127
- 8-8 Troubleshooting 130
- Appendix A 131
- SCSI Cables and 131
- Connectors 131
- SCSI devices is shown below 133
- Table A.1 SCSI Cable Vendors 136
- Appendix B 141
- Audible Warnings 141
- B-2 Audible Warnings 142
- Appendix C 143
- Glossary 143
- C-2 Glossary 144
- C-4 Glossary 146
- C-6 Glossary 148
- C-8 Glossary 150
- C-10 Glossary 152
- IX-2 Index 154
- Index IX-3 155
- IX-4 Index 156
- Customer Feedback 157
Related products and manuals for Peripheral controllers LSI MegaRAID SCSI 320-2 RAID Controller Series 518
(3 pages)© 2020, manymanuals.com. All rights reserved. | 0.183 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals